- YOUTUBE CHIRP PROGRAMMING HOW TO
- YOUTUBE CHIRP PROGRAMMING INSTALL
- YOUTUBE CHIRP PROGRAMMING DOWNLOAD
Several people have reported newly purchased units with the following frequencies preprogrammed from the factory. To enter 451.0125 the step can be set to either 2.5K, 6.25K or 12.5K and you must press or. To enter 451.00625 the step must be set to 6.25K and you must press or. To enter 451.0025 the step must be set to 2.5K and you must press or. You must have Menu 1 STEP set to the correct step size. You must enter the next higher digit or use the up/down arrow keys to change the rest of the digits. If the third decimal place is not 0 or 5 the radio will round down to the nearest step. You cannot enter a frequency with more than 3 decimal places, such as 451.0025 or 451.00625, using only the number keys. The radio will only accept 0 or 5 in the third decimal place. The kHz part of the frequency (the digits to the right of the decimal point) must be divisible by the step size (Menu 1 STEP). When entering frequencies via the keypad in VFO (Frequency) Mode the radio will only accept 6 digits three before the decimal point and three after the decimal point. Mic audio can possibly interfere with transmitted tones. Setting Menu 16 DTMFST to OFF disables the sidetone but doesn not mute the mic. Setting Menu 16 DTMFST to DT-ST or DT+ANI mutes the microphone preventing it from interfering with transmitted DTMF and 1750 Hz burst tones. The mic can pick up the sidetone from the speaker and overdrive or distort the transmitted tones. Pressing keypad keys while transmitting does not mute the mic. If Menu 16 DTMFST is set to ANI-ST, the internal microphone is hot when DTMF or 1750 Hz burst tones are transmitted. Pressing the key sends "0" instead of "D". On firmware version BFS311, and possibly others, it is not possible to send a DTMF "D" tone. The up/down arrow keys srcoll through the standard tone frequencies. CTCTSS transmit and receive tone frequencies can be set via the numeric keypad to any frequency from 60.0 to 259.9 Hz in 0.1 Hz increments. The UV-5R has a 26 MHz reference oscillator. In dual watch mode (Menu 7 TDR ON) the receiver on time is doubled to approximately 0.4 second due to checking two channels instead of one.īattery saver is activated after ~9 seconds of no receive and no keypad activity and is not active while scanning. When Menu 3 SAVE is enabled, the receiver is periodically turned off to reduce power consumption. 
Unit was purchased in 11/2013 and may have been manufactured the same month.
3 UV-5R Stock Dual Band Helical Antennaīaofeng UV-5R Notes (BFS311 Firmware) Test Unit. 
1 Baofeng UV-5R Notes (BFS311 Firmware).
YOUTUBE CHIRP PROGRAMMING DOWNLOAD
Next, open the app and download the data from the radio.
YOUTUBE CHIRP PROGRAMMING INSTALL
Once the installer has downloaded, double-click on its icon and the installer will install CHIRP on your computer. On the next page, look for the reccomended version for your operating system (highlighted in green) and click on it to download the installer. To install CHIRP, first go to the CHIRP website and click the “get it!” button.
YOUTUBE CHIRP PROGRAMMING HOW TO
In this post, we’ll show you how to program a BTECH UV-5X3 with CHIRP.ĬHIRP runs on Windows, MacOS, and Linux operating systems, but in this post, I’ll be describing how to install and use the Windows version of CHIRP. You can use CHIRP to program 11 different BTECH models, including our amateur radios and our GMRS and MURS radios. One of the most frequently asked questions that we get here at BTECH is, “How do I program the channel memories in my UV-5X3?” The answer is, “Get CHIRP!” CHIRP is a free, open-source application for programming many different radios from dozens of manufacturers.
0 kommentar(er)
